ServicesFrame Straightening
Frame Straightening in Reedley
After a collision, the steel structure beneath your car can end up out of position while the panels look almost untouched. We measure it, pull it back to factory dimensions and measure again. The same small crew stays with your vehicle from the first check to the final alignment.

Straightening the structure your car is built around
On a modern unibody car there is no separate frame to point to. The rails, aprons, pillars and floor pan form the body itself, and all of them carry load. An impact that moves them just a few millimeters can change how the doors shut, where the wheels point, and how your vehicle absorbs a future crash.
Frame straightening returns that structure to the shape the manufacturer engineered. We clamp your vehicle to anchor points, compare key measuring points with published factory dimensions, and pull in controlled steps until the readings line up. Pickups and older body-on-frame vehicles with a ladder frame get the same measure-and-pull method.
We are a small shop, so one crew measures your car, does the pulls and signs off on the result. Nobody new picks up the job midway, and you never have to tell the story of the accident twice.
What frame straightening includes
Pre-repair measuring
We check reference points under the car and in the engine bay against the manufacturer's specs. This shows exactly where the structure moved and how far.
Anchoring and controlled pulls
Your vehicle is clamped at solid points, then pulled in small steps from the right direction. We measure between pulls so the metal is not overcorrected.
Sectioning or replacing parts that cannot be pulled
Some high-strength steels are not meant to be heated or straightened. When a rail or apron is past repair, we replace or section it following the manufacturer's repair procedure and tell you why.
Post-repair measuring
Once the pulls are done, we measure the same points again. You can see the before and after numbers.
Alignment and system checks
Straightened structure is followed by a wheel alignment, and we check whether driver-assist sensors need recalibration after the repair.
Signs your car may need frame work
Panels and doors sit out of line
Gaps around the hood, trunk or doors that are wider on one side, or a door you now have to push hard to latch, usually mean the opening around it has moved.
Your car drifts or crabs down the road
A steering wheel that sits crooked on a straight road, or a rear end that seems to trail at an angle, can mean the suspension mounts shifted along with the structure.
Tires wearing unevenly after a crash
When one edge of a tire wears down within a few months, bent mounting points may be the cause. An alignment by itself will not correct that.
Fresh squeaks, rattles or wind noise
A slightly twisted body flexes in new ways over bumps and can open small gaps around the door seals.
Bent or buckled metal underneath
Creases in the rails, floor or inner fenders are a clear sign of structural damage. Dropping a wheel off a ditch edge or into a deep pothole on a rural road can cause it too, not only a collision.
How a frame straightening job runs
- 1
Talk it through by phone
You tell us what happened and how the car is driving. We explain what we will look for and set a time to bring your vehicle in.
- 2
Inspect and measure
We put your car up, remove what is needed to reach the structure, and take measurements. Then we go over what we found and write up the estimate line by line.
- 3
Straighten and repair
The same crew sets up the pulls, works the structure back into place, and replaces anything that should not be reused. If we find hidden damage once parts come off, we stop and talk to you before going further.
- 4
Verify, align and hand back
We measure again, align the wheels, test drive the car, and walk you through the results when you pick it up. Any remaining body or paint work is done by the same people before it leaves.
What moves the cost of frame straightening
There is no flat price for structural work because no two impacts bend a car the same way. The estimate depends on what the measurements show once we can see the structure. We give you a written, itemized estimate and explain each line before we start.
- How far and where the structure moved
- A single rail pushed back a little takes fewer pulls than damage that runs from the front apron into the pillar.
- Pull versus replace
- Parts the manufacturer says must be replaced, not straightened, add parts cost and labor for sectioning and welding.
- Vehicle type and materials
- Aluminum structures and some high-strength steels need specific procedures. Trucks with a separate frame are set up differently from unibody cars.
- What comes off to reach it
- Bumpers, radiator supports, suspension parts or interior trim may need removal and reinstall, which adds hours.
- Alignment and sensor calibration
- Most structural repairs end with an alignment, and some vehicles also need camera or radar calibration afterward.
Frame straightening questions
Something not covered here? (559) 315-1279
Is a car safe to drive after frame straightening?
When the structure is measured back to factory dimensions and damaged parts are replaced where required, the car is built to handle loads the way it was designed to. That is why we measure before and after rather than judging by eye. We show you the final numbers so you are not just taking our word for it.
Will my car be totaled if the frame is bent?
Not necessarily. Many bent frames are straightened every day. Whether a car is totaled usually comes down to the repair cost compared with the car's value, which your insurer decides. We can give you a clear estimate of the structural work so that decision is based on real numbers.
Will insurance pay for frame straightening?
If the damage comes from a covered accident, structural repair is normally part of the insurance claim. We document the measurements and send the adjuster what they need, and our Insurance Claims page explains how that works with us. The adjuster still makes the coverage decision.
How long does frame straightening take?
It depends on how much moved and whether parts need to be ordered. A simple pull may take a day or two of shop time, while bigger repairs that need replacement parts take longer. We give you a realistic timeline after measuring and keep you posted if anything changes.
Can I drive my car to the shop if I think the frame is bent?
If it steers normally, the lights work and nothing is rubbing a tire, a short careful drive is often fine. If it pulls hard, makes grinding noises or has a wheel sitting at an odd angle, have it towed. Tell us how it is behaving when you phone and we will help you decide.

Get your car measured and straightened right
Tell us what happened and how your vehicle is driving now. We will explain what we check, what the estimate covers, and when you can bring it in from Reedley, Dinuba, Sanger or nearby.